[. . . ] WARNING: This apparatus must be earthed. The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Serial No. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. [. . . ] ATW (Automatic Tracing White Balance) System is incorporated into the WV-CP220 series. This system has a colour temperature sensor for accurate detection of light source colour temperatures projected onto objects without affect of ambient temperatures and light intensity according to the angle of incident. In addition, ability to shoot indoor scenes with a fixed iris lens by use of Electronic Light Control (ELC) function. The built-in AGC (Automatic Gain Control) allows to obtain a clear picture under the low light condition. FEATURES · Minimum illumination of 0. 5 lx at F0. 75 [equivalent 1. 5 lx at F1. 4] and Signal-to-Noise ratio of 46 dB by employing a 1/3 inch interline transfer CCD image sensor with 512 (H) x 582 (V) pixels. · 330 lines of horizontal resolution · Optional C-mount lens can be used together with optional Lens Mount Converter (C-mount adaptor) WV-AD20. · Selectable internal sync (INT), line-locked sync (LL) or Multiplexed Vertical Drive (VD2) for WVCP220/WV-CP224. · Automatic Gain Control (AGC) (+15dB) and Automatic Tracing White Balance Control (ATW) are built-in. -3- PRECAUTIONS · Do not attempt to disassemble the camera. · Do not expose the camera to rain or moisture, or try to operate it in wet areas. Moisture can damage the camera and also create the danger of electric shock. Do use caution when operating the camera in the vicinity of spot lights or other bright lights and light reflecting objects. · Do not operate the camera beyond its temperature, humidity or power source ratings. Do not use the camera in an extreme environment where high temperature or high humidity exist. Use the camera under conditions where temperatures are within -10°C - +50°C, and humidity is below 90%. The input power source is 220 - 240V AC 50 Hz for WV-CP220, 12V DC for WV-CP222 or 24V AC 50 Hz for WV-CP224. -4- MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS (7) (8) (6) (9) (10) (1) (4) (2) (3) (11) @ ! (5) (5) (5) WV-CP220 WV-CP222 -5- WV-CP224 (1) Auto Iris Lens Connector This 4-pin connector supplies the power and DC control signal to the auto iris lens. (2) Flange-back Adjusting Ring This ring is used to adjust the back focal length or picture focus by rotating this ring. (3) Lens (Option) See page 11, 12, 13, 14 and 15 for details on lens selection. Standard C-mount lens can be used with the camera by use of optional lens mount converter (C-mount adaptor) WV-AD20. (4) Camera Mounting Screw Hole This threaded hole (1/4" - 20) is used to mount the camera onto a mounting bracket or tripod. (5) Video Output Connector (VIDEO OUT) A 1. 0 V[p-p] / 75 composite video signal is provided at this connector. Whenever the multiplexed vertical drive (VD2) signal is supplied to this connector, the camera synchronization mode is automatically set to Vertical Drive Lock. (6) AC Power Cord (7) Sync Selection Switch (LL/INT) (WV-CP220/WV-CP224) This switch is used to select the camera synchronization mode. [. . . ] Loosen screws on the flange-back adjusting ring. PREVENTION OF BLOOMING AND SMEAR When the camera is faced toward spot light or other bright lights and light reflecting objects, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. Flange-back Adjusting Ring , , , , , , Smear Bright object 2. Caution: Do not turn this ring too much to counterclockwise as this could damage the inner glass and CCD image sensor. Note: Do not apply the extreme torque (0. 5 kg. cm is recommended) to the screw on the Flangeback Adjusting Ring. LENS MAINTENANCE AND CLEANING 1. [. . . ]